SFSB90 90 Lb. Siphon Feed Abrasive Blaster Assembly & Operating Instructions
8
PACKAGE CONTENTS
l
OMPONENTS
ASSEMBLY
the upper portion of the Handle with the holes in the Abrasive Tank.
OOT AND WHEELS
of the Foot with the holes in the lower portion of the Handle.
ks
of the Wheel Axle.
UPPORT POST
end of the Support Post with the hole in the front of the Foot.
port Post.
nk.
iver and a wrench.
o each end of the Abrasive Hose. Firmly push the end of the Abrasive Hose onto
1
• 8 Ft Hose
• Tank
• Hood
• Funne
C
1. Hose Hook
2. Tank
3. Handle
4. Hose Clamp
5. Tire
Stand
6. Tank
. Align the holes in
1
2. Place Flat Washer on a Long Screw and insert Screw through Handle and Abrasive
Tank.
e a Flat Washer and Lock Nut onto screw end and hand tighten.
3. Plac
4. Repeat steps 2-3 for remaining hole in Handle.
, fully tighten screws.
5. Using a Phillips head screwdriver and a wrench
F
1. Align the holes in the rear
2. Slide the Wheel Axle through the holes in the Handle and Foot until the Wheel Axle stic
out approximately 3.5" inches on both sides of the Handle.
and slide a Wheel onto both ends
3. Place a Wheel Washer onto both ends of the Wheel Axle
4. Place a Wheel Washer onto both ends of the Wheel Axle - make certain that the air valve in
the wheel is facing out.
gh each of the holes in the Wheel Axle and bend them so the Wheels cannot slide off the Wheel Axle.
5. Insert Cotter Pin throu
S
1. Align the hole in the
2. Place a Flat Washer on a Long Screw and insert Screw through the Foot and Sup
3. Place Flat Washer and Lock Nut onto end of Screw and hand tighten.
les in the Abrasive Ta
4. Align the two holes in the upper portion of the Support Post with the ho
5. Place a Flat Washer on a Short Screw and insert Screw through Support Post and Abrasive
Tank.
e a Flat Washer and Lock Nut on Screw and secure in place with a phillips head screwdr
6. Plac
7. Repeat steps 5-6 for remaining hole in Support Post.
tighten the Screw installed in step 2.
8. Using a Phillips head screwdriver and a wrench, fully
brasive Gun and Hose
A
1. Place a Hose Clamp ont
the abrasive inlet on the Abrasive Gun.
at it is overlapping both the Abrasive Hose AND the
2. Position one of the Hose Clamps so th
abrasive inlet of the Abrasive Gun.
a screwdriver and firmly push the opposite end of the Abrasive Hose onto the abrasive
3. Tighten Hose Clamp in place with
outlet, located at the base of the Abrasive Tank. Note: There is an air hole in the abrasive outlet - DO NOT cover this air
hole with Abrasive Hose.
4. Position the remaining Hose Clamp so that it is overlapping both the Abrasive Hose AND the
abrasive outlet of the Abrasive Tank. Tighten Hose Clamp in place with a screwdriver.
(12 páginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais